TOOLS NEEDED

Tape Measure

Tin Snips or
Miter Saw

Rubber Roller
(Optional)

PREP
  • Clean the surface you are covering thoroughly – removing all wax, dust and grease. For best results, use alcohol wipes to clean surfaces.
  • Make sure all painted or textured surfaces are lightly sanded and then cleaned for maximum adhesion.
  • If caulking exits, remove caulking and clean thoroughly.
  • All porous surfaces (for example: wood) should be primed (sanded and/or painted) for maximum adhesion.
  • Dry all surfaces thoroughly after cleaning.
CUT
  • Measure the surface you are covering with a tape measure.
  • Cut the DécorWorks plastic shape to your specifications using tin snips or a miter saw.
PLACE
  • Peel off paper backing and align the DécorWorks plastic shape to the area of placement.
  • Place the DécorWorks plastic shape and press down on it using either a rubber roller or your hand to ensure long-lasting and even adhesion.
  • For DécorWorks shapes that do not have an adhesive backing, DécorWorks recommends using tube adhesive or high-bond, double-sided tape. If you use tube adhesive, make sure it is intended for bonding plastic or PVC plastic. To ensure adhesion, test a certain area first. If you do not want to use adhesive, DécorWorks recommends pre-drilling holes and using decorative nails or screws.
CLEAN & MAINTAIN
  • Do not expose DécorWorks plastic shape to constant heat or moisture.
  • Clean the DécorWorks plastic shape using a damp sponge or cotton cloth with mild soap and warm water, take caution and do not completely soak the surface.
  • Do not use any strong chemical cleaning agents or abrasives.
TOOLS NEEDED

Tape Measure

Utility Knife or
Tin Snips

Steel Straight Edge

Rubber Roller

PREP
  • Clean the surface you are covering thoroughly – removing all wax, dust and grease. For best results, use alcohol wipes to clean surfaces.
  • Make sure all painted or textured surfaces are lightly sanded and then cleaned for maximum adhesion.
  • If caulking exists, remove caulking and clean thoroughly.
  • All porous surfaces (for example: wood) should be primed (sanded and/or painted) for maximum adhesion.
  • Dry all surfaces thoroughly after cleaning.
CUT
  • Measure the surface you are covering with a tape measure.
  • Cut the DécorWorks plastic sheet to your specifications using a utility knife and steel straight edge on a flat surface.
PLACE
  • Fold back 1/3 of the paper backing. Start at the bottom of the surface you want to cover and place the DécorWorks plastic sheet. Apply light pressure in an upward direction. Do not remove the top protective film.
  • Continue to peel the paper backing and apply light pressure as you place the DécorWorks plastic sheet on your surface.
  • Once the DécorWorks plastic sheet has been fully applied, press across the sheet with a rubber roller to ensure long-lasting and even adhesion.
  • If the DécorWorks plastic sheet has a top protective film, remove this once the sheet is properly adhered to your surface.
CLEAN & MAINTAIN
  • Do not expose DécorWorks plastic sheet to constant heat or moisture.
  • Clean the DécorWorks plastic sheet using a damp sponge or cotton cloth with mild soap and warm water, take caution and do not completely soak the surface.
  • Do not use any strong chemical cleaning agents or abrasives.

WARNINGS:

Product cannot be used near heat, fire or excessive water. Do not use near fireplaces, kitchen stove tops, inside showers, counter top covers or outside. Plastic shapes and sheet expand and contract with large temperature variation. Let the product acclimate in the room it will be installed in for 48 hours before installing. For newly painted walls, make sure to wait 3 weeks before applying product. Not recommended for use on textured walls. If you are unsure about your surface, try testing one shape or sheet first. Leave on the wall for 2-3 days before applying the rest of your shapes or sheet.